The clearest signs of a slab leak are a water meter that keeps moving with every fixture off, a warm spot on the floor, the sound of running water in a quiet house and a water bill that rises without a change in habits. Confirm a leak with EPA’s two-hour meter test, then call a licensed plumber, because slab leak repair is not a do-it-yourself job. Bienvenu Brothers finds and repairs slab leaks in Metairie, New Orleans and the surrounding communities. Our BBB A+ Rated, 4th generation family-owned company is 100% recommended on Facebook and an Angi Super Service Award winner. We work under Louisiana master plumber license LMP#7214WSPS, stay fully insured and have served South Louisiana since 1937. Contact Bienvenu Brothers or call (504) 835-7783 if your meter keeps moving.
This guide explains what a slab leak is, what causes one, the nine signs to check, how to tell a slab leak from other leaks, how to confirm it with your meter, what to do next and what Metairie and New Orleans homeowners should know about utilities, soil and rainfall.
What a Slab Leak Is
A slab leak is a leak in a water supply line that runs under or inside the concrete slab a house sits on. HomeServe explains that plumbers lay the pipes before the foundation is poured, so a crack in one of those pipes sits beneath the concrete, out of sight.
Slab leaks are hard to notice because water may never reach the surface. The signs show up in floors, walls, sounds, smells and your meter instead.
Not every home has one to worry about. Metairie and New Orleans homes range from slab-on-grade ranch houses to raised bungalows, shotguns and doubles, so check your foundation type first, because only a home built on a slab can have a slab leak.
What Causes Slab Leaks
Consumer plumbing guides list five common causes. The table shows how each one damages a line under the slab.
| Cause | What happens | Source |
|---|---|---|
| Corrosion | Galvanized steel, cast iron and older copper pipes corrode over time and develop leaks | Angi |
| Abrasion | Small vibrations can wear plastic pipes over time | Angi |
| Soil movement | Soil that shifts under the home can stress pipes and the foundation, and soil that absorbs water and expands can damage pipes | Angi |
| High water pressure | Buried pipes are often under significant pressure, and pressure can rise after the ground shifts | Angi |
| Installation problems | A foundation that was not installed properly could cause a future slab leak. Plumbers lay the pipes before the slab is poured, so repairs mean reaching under concrete | Angi and HomeServe |
Nine Signs of a Slab Leak
Think of the signs in two groups. A moving meter, a higher bill and the sound of water tell you that water is leaking somewhere. Warm floor spots, a damp slab, new floor-level cracks, a musty smell with no visible source and standing water at the foundation suggest the water may be under the floor. Signs from both groups together make a slab leak the leading suspect, and a plumber confirms it with equipment.
| Sign | What you notice | What it tells you | Other causes to rule out |
|---|---|---|---|
| 1. A meter that moves with every fixture off | The dial or low-flow indicator keeps turning | Water is leaking somewhere on the house side or in the line to the meter | A running toilet, a dripping faucet, irrigation, a softener or an ice maker |
| 2. Warm or hot spots on the floor | A patch of tile, wood or concrete feels warmer than the floor around it | Points to the slab, because warm areas often follow a leaking hot water line | Sunlight, heating or cooling ducts |
| 3. The sound of running water | A hiss or trickle when every fixture is off | Water is moving where it should not, and the leak may sit in a wall or under the slab | A running toilet, softener cycle, irrigation or water heater |
| 4. A higher water bill | Usage rises with no change in habits | There is a leak, or more water use, somewhere | Guests, pool fill, a longer billing period, a new smart meter |
| 5. Lower water pressure | Weak flow at several fixtures at once | Water escapes before it reaches the fixtures | Clogs, a failing pressure regulator, utility work |
| 6. Wet or damp spots | A dark, damp patch on the slab, or carpet near walls that stays damp | Water may be seeping up from below | An appliance leak, a roof or window leak, a wall leak |
| 7. A musty or earthy smell | A persistent odor with no visible water | Moisture is feeding mold or mildew | High humidity, wet crawl space, condensation |
| 8. New cracks near the floor | Cracks in lower walls, baseboards or tile | Moisture or movement under the slab | Foundation settling or a structural problem, so have a professional evaluate them |
| 9. Water pooled at the foundation | Water that stays for days after dry weather | Water from a leak may be surfacing | Rain, irrigation, drainage and downspouts |
Warm or Hot Spots on the Floor
A leaking hot water line can warm the concrete above it. This Old House says these warm areas typically follow the path of a leaking hot water pipe, and HomeServe says a leaking hot water pipe under the slab can make specific spots on the floor feel warm. Walk the house in bare feet or socks and note any patch that feels warmer than the floor around it. A leak in a cold water line has no warm spot to give it away, so the meter, sound and moisture signs matter more in that case.
Sounds of Running Water
If you hear hissing or running water while every fixture and appliance is off, water is moving where it should not. This Old House says the leak may sit behind drywall, and HomeServe lists a hissing sound or the noise of running water when everything is off as a reason for an inspection. Listen in a quiet house with the dishwasher, washer and ice maker idle, and note where the sound is loudest. A running toilet, a softener cycle or an irrigation timer can make a similar sound, so check those first.
A Meter That Moves and a Bill That Climbs
A moving meter is the strongest evidence that water is leaking, and a higher bill is how many homeowners first notice it. HomeServe says a sudden bill increase with no change in usage can point to a leak, and This Old House says a significant or unexpected increase is worth investigating. Compare your usage with the same month last year and count the days in the billing period before you suspect a leak. Our guide to a high water bill and hidden leaks walks through the bill and meter checks, including a worksheet that turns a meter change into gallons per day.
Slab Leak or Something Else? How to Rule Out Other Leaks
A slab leak is usually a diagnosis of exclusion plus two or more matching signs. This table rules out the common look-alikes before you call.
| Rule out | How to check | What it tells you |
|---|---|---|
| Toilets | Add a few drops of food coloring to the tank, wait 10 minutes without flushing and look for color in the bowl | Color means a flapper or fill valve leak, covered in our guide to fixing a running toilet |
| Faucets, shower heads and hose bibs | Look and listen for drips at every fixture, indoors and out | A drip can move the meter, but it does not warm the floor |
| Water heater, softener and ice maker | Check the base, the relief valve pipe and the supply lines for water, and see our guide to common water heater problems | A leak there shows water at the appliance |
| Irrigation and pool fill lines | Close the outdoor valves and rerun the meter test | If the meter stops, the leak was outdoors |
| The main shutoff | Close the valve at the house and watch the meter | If the meter stops, the leak is on the house side. If it keeps moving, the leak is between the meter and the house |
| Wall leak versus slab leak | Note where the sound is loudest and whether the drywall is damp or the floor is warm or damp | Damp drywall tends to point to a wall, and a warm or damp floor tends to point to the slab |
How to Confirm a Slab Leak With Your Water Meter
The meter test takes two hours and no tools. Work through the steps in order.
- Stop all water use. Close faucets, pause the dishwasher and washer, and make sure no one flushes a toilet. Confirm that the irrigation timer, ice maker and any softener cycle are idle.
- Record the reading and the time. Write down every digit, including any small test dial or low-flow indicator.
- Wait two hours without using any water.
- Read the meter again. EPA says that if the reading has changed at all, you probably have a leak.
- Close the main shutoff and watch the meter. If the meter stops, the leak sits inside the house. If it keeps moving, the leak sits in the line between the meter and the house. Our guide shows how to shut off the main water valve.
Smart meter owners can run a similar check from a phone. The S&WB customer portal shows what time of day you use water and alerts registered customers when a meter measures over 4 gallons per hour of continuous use over a 48-hour period, which equals about 96 gallons per day. S&WB recommends that customers not lift the smart meter lid. Jefferson Parish customers can use DropCountr, which shows daily, monthly and annual use and flags unusual or continuous use. A slow slab leak can run below the S&WB alert level, so run the meter test even when no alert arrives.
What to Do If You Suspect a Slab Leak
- Confirm with the meter test. Two matching signs and a moving meter justify a call.
- Shut off the main if you hear a strong rushing sound or see water appearing. This Old House advises locating the main valve in advance, usually near the front of the house by the meter.
- Document what you find. Photograph damp spots, cracks and the meter readings, and save the bills that show the increase.
- Dry wet areas quickly. EPA advises drying water-damaged areas within 24 to 48 hours to prevent mold growth.
- Leave the digging to the professionals. Do not drill or break the floor to look for the pipe.
- Call a licensed plumber with leak detection equipment. Ask which tools they use, what they found and which repair options fit your home, and keep the invoice.
Slab Leak Signs: DIY or Professional?
You can gather the evidence yourself. A leak under concrete needs a licensed plumber to locate and repair it.
| Task | Reasonable for a homeowner | Call a professional when |
|---|---|---|
| Compare bills and count billing days | Yes | The jump is unexplained after you check the dates |
| Run the two-hour meter test | Yes | The meter moves, or the meter box is hard to reach |
| Run the toilet dye test and check fixtures and appliances | Yes | Those are clear and the meter still moves |
| Close the main and watch the meter | Yes, when the valve works | The valve sticks, leaks or will not close fully |
| Locate a leak under the slab | No | Always, because it takes acoustic, thermal and pressure testing tools |
| Open the slab, reroute or repipe a line | No | Always, through a licensed plumber |
| Evaluate new cracks in walls or floors | No | Always, because a structural problem can cause similar cracks |
How Plumbers Find and Repair Slab Leaks
Detection comes first. Our water leak detection and repair service uses acoustic listening, thermal imaging and pressure testing to pinpoint a leak before anyone opens a wall or breaks a slab. Acoustic devices pick up the sound of escaping water, thermal cameras show temperature differences and pressure tests isolate sections of pipe.
Repair comes second, and the right approach depends on the pipe material, the number of leaks and the layout of the home. The table lists the four approaches that consumer plumbing guides describe.
| Option | What it involves | When plumbers use it | Source |
|---|---|---|---|
| Spot repair | The plumber opens the slab at the leak and replaces the damaged section with new pipe | A small, accessible leak | HomeServe and This Old House |
| Reroute | A new line runs above ground through the attic or walls, and the slab stays intact | Short damaged sections | HomeServe and This Old House |
| Pipe relining | A liner goes inside the damaged pipe to seal the leak from within | Often minor repairs to copper pipe | HomeServe and This Old House |
| Repipe | The plumber replaces pipes throughout, which can involve digging up concrete | Multiple leaks | HomeServe |
Our post on slab leak repair dos and don’ts covers what to avoid while you wait for the repair.
Slab Leaks in Metairie, New Orleans and Nearby Communities
Five local facts shape how slab leak signs show up in our service area. The table shows what each one means for your home.
| Local factor | What the data shows | What it means for your home |
|---|---|---|
| Ground movement | A NASA and university study, reported by NASA JPL, used data from June 2009 to July 2012 and found sinking of up to 2 inches a year in some places, with notable subsidence in Metairie and in the Upper and Lower Ninth Ward. The study cites groundwater pumping and dewatering as primary contributors. | Angi lists soil movement among slab leak causes, but neither source says how often subsidence breaks pipes. Treat it as one possible factor. |
| Rainfall | LSU AgCenter reports that New Orleans averages 62 inches of rain a year. | Rain can pool near the foundation. This Old House advises checking whether standing water stays for days after dry weather. |
| Humidity | LSU AgCenter places most of Louisiana in the hot, humid climate region. | A musty smell is easy to dismiss here. Dry wet areas quickly and run the meter test. |
| Utility tools | The S&WB customer portal shows when you use water and alerts at over 4 gallons per hour of continuous use over 48 hours. Jefferson Parish’s DropCountr shows daily, monthly and annual use. | Use overnight or empty-day readings to spot continuous use, and remember that a small leak can run below the alert level. |
| Responsibility | Jefferson Parish’s water director told Fox 8 in June 2026 that the parish is responsible from the main up to the back of the meter. The S&WB FAQ states that leaks on private property are the property owner’s responsibility. | A slab leak sits on the homeowner’s side of the meter, so the repair is yours to arrange. |
Utility rules change. Confirm where your utility’s responsibility ends for your address before you rely on this table.
We find and repair slab leaks on both banks of Jefferson Parish and across Orleans Parish. Choose the community nearest you:
- Metairie, LA
- New Orleans, LA
- Kenner, LA
- Harahan, LA
- River Ridge, LA
- Gretna, LA
- Harvey, LA
- Marrero, LA
- Westwego, LA
Slab Leak Signs FAQs
These are the questions Metairie and New Orleans homeowners ask us most often about the signs of a slab leak.
What are the first signs of a slab leak?
The earliest signs are usually a water meter that keeps moving with every fixture off, a higher water bill with no change in habits, the sound of running water in a quiet house and a warm spot on the floor. This Old House also lists low water pressure, standing water near the foundation, a musty smell, damp carpet and cracks in lower walls or baseboards. Run the two-hour meter test first, because several of these signs have other causes. Our guide to the signs of water leaks in New Orleans homes shows what leaks look like in local houses.
Can I have a slab leak without seeing any water?
Yes. The leak sits in pipes under or inside the concrete, so water may never reach the surface. The signs show up elsewhere: a meter that moves, warm floor spots, the sound of water, a higher bill, a musty smell or new cracks near the floor. HomeServe notes that dampness from a slab leak can lead to mold and mildew growth. A plumber confirms the leak and its location with detection equipment.
Why are there warm spots on my floor?
A leaking hot water line under the slab can warm the concrete above it. This Old House says warm areas typically follow the path of a leaking hot water pipe, and HomeServe says the same about specific spots on the floor. Sunlight through a window and heating or cooling ducts can also warm a floor, so check the meter before you decide. Call us if a warm spot appears and the meter moves with everything off.
Is the sound of running water in my walls a slab leak?
It might be, but it is not the only explanation. This Old House says running water heard while all fixtures are off can mean a leak under the slab, and that the leak may sit behind drywall. Rule out a running toilet, a water softener cycle and irrigation first, then run the meter test. If the meter moves and you cannot find the source, call us to locate the leak.
How do I check for a slab leak with my water meter?
Stop all water use, record the meter reading and wait two hours without using any water. EPA says that if the reading has changed at all, you probably have a leak. Then close the main shutoff valve at the house and watch the meter. If the meter stops, the leak is on the house side. If it keeps moving, the leak is in the line between the meter and the house.
How can a smart meter or utility app help me find a slab leak?
Look for continuous use through the night, or on a day when nobody was home. The S&WB customer portal shows what time of day you use water, and S&WB alerts registered customers when a meter measures over 4 gallons per hour of continuous use over a 48-hour period. Jefferson Parish customers can use DropCountr, which shows daily, monthly and annual use and flags unusual or continuous use. A small slab leak can run below the S&WB alert level, so run the meter test even without an alert.
Does low water pressure mean I have a slab leak?
Not by itself. This Old House says water escaping from a broken line beneath the slab can reduce pressure throughout the house, and it adds that clogs can cause the same symptom. Low pressure at one fixture usually points to that fixture, while low pressure at several fixtures at once is worth more attention. Check the meter, and call us if it moves.
Can a slab leak cause mold or a musty smell?
Yes. This Old House says a persistent musty or earthy smell can signal mold or mildew, and that carpet which is damp near walls and keeps returning after drying can point to water seeping up from below. EPA advises drying water-damaged areas within 24 to 48 hours to prevent mold growth. Dry the area, run the meter test and call us if the dampness returns.
What causes slab leaks?
Angi lists corrosion in galvanized steel, cast iron and older copper pipes, abrasion from small vibrations in plastic pipes, shifting soil under the home, high pressure in buried lines and poor installation. HomeServe adds that plumbers lay these pipes before the foundation is poured, so a crack sits beneath concrete. A plumber can tell you which cause applies to your leak once the pipe is located.
Do cracks in my walls or floor mean a slab leak?
They can, but they are a weak sign on their own. This Old House says moisture rising from below can crack lower walls or baseboards, and it warns that a structural problem can cause similar cracks. Have a professional evaluate new cracks, and run the meter test to see whether water is involved.
Should I shut off the water if I suspect a slab leak?
Yes, when you hear a strong rushing sound or see water appearing. This Old House advises shutting off the main water valve in those cases and locating the valve in advance, usually near the front of the house by the meter. Photograph the damp spots and the meter readings before you call, and dry wet areas quickly.
Can I fix a slab leak myself?
No. This Old House states that slab leak repair is not a DIY job, and HomeServe says the repair needs an experienced plumber with slab leak detection tools. The pipe sits under concrete, finding the exact spot takes specialized equipment and the repair may involve opening the slab or rerouting the line. You can do the meter test and close the main, and a licensed plumber should do the rest.
How do plumbers find a slab leak without breaking the floor?
Leak detection combines tools. Acoustic listening devices pick up the sound of escaping water, thermal imaging cameras show temperature differences, and pressure testing isolates sections of pipe. We use these tools to narrow the search before anyone opens the slab. Once we locate the leak, we explain the repair options and describe the work for your records.
How is a slab leak repaired?
HomeServe describes four approaches that plumbers generally choose among: a spot repair that opens the slab at the leak and replaces the damaged section, rerouting a new line above ground, relining the damaged pipe and repiping when there are multiple leaks. Angi notes that you may need to reroute the pipe or even repipe the house, depending on the size and location of the leak. We explain the options that fit your home after we locate the leak.
Who is responsible for a slab leak, me or the water utility?
A slab leak sits on the homeowner’s side of the meter. Jefferson Parish’s water director told Fox 8 in June 2026 that the parish is responsible from the main up to the back of the meter, and the S&WB FAQ states that leaks on private property are the property owner’s responsibility. Ask your utility where its responsibility ends for your address.
When to Call Bienvenu Brothers About a Slab Leak
Call us when the meter moves with everything off and you also see a warm floor spot, hear water, notice dampness or find new cracks near the floor. Our licensed plumbers locate the leak, explain the repair options and describe the work so you have a record. Our slab leak repair service covers leaks in the pipes under your slab, and our general plumbing repairs cover the fixtures, valves and supply lines that cause look-alike problems. Call (504) 835-7783 or Contact Bienvenu Brothers to schedule a visit. The table shows what you get when you choose Bienvenu Brothers.
| What We Offer | What It Means for You |
|---|---|
| Louisiana master plumber license LMP#7214WSPS | A state-licensed master plumber handles your leak repair, not an unlicensed handyman. |
| Fully insured | You stay protected if something goes wrong on your property. |
| BBB A+ Rated | An independent organization rates our business practices and tracks complaints, and you can read the profile yourself. |
| 100% recommended on Facebook | Customers recommend our work in public reviews that anyone can read. |
| Angi Super Service Award winner | Angi recognizes companies that earn consistently high ratings from verified customers. |
| Leak detection with acoustic, thermal and pressure testing tools | We locate hidden leaks before anyone opens a wall or breaks a slab. |
| Same-day scheduling and 24/7 emergency service | Help is available when a leak will not wait, whatever the hour. |
| 4th generation, serving since 1937 | Four generations of experience with South Louisiana homes and plumbing. |
| Clear repair records | You leave with a description of the leak and the repair for your files. |
Bienvenu Brothers finds and repairs slab leaks across Metairie, New Orleans and nearby communities. Licensed, fully insured, BBB A+ Rated and available 24/7 for emergencies. Call (504) 835-7783 to schedule a leak check.